Help for Current Versions of MX
When asking for help, use Quick System Info from MX Tools. It will be properly formatted using the following steps.
1. Click on Quick System Info in MX Tools
2. Right click in your post and paste.
CharlesV wrote: Fri Feb 28, 2025 10:51 am
Now, go back in and change the settings to Never if you dont want it to sleep, etc etc..
Sorry, this old man needs some clarification. Go back in where? The Power Manager? Which tab (System, Display or both)?
CharlesV wrote: Fri Feb 28, 2025 10:51 am
testing - you might want to set the "15 min" as mentioned above to say 5 min and see if your machine does it properly AND that you can come out of it properly... Then set it all to never and see how that works.
This is also the Power Manager, right? Which tab (System, Display or both)?
Does Presentation Mode need to be turned off for the system or display to automatically suspend?
Same place as making the initial changes. (ie xscreensaver and then in power manager )
Both Display and system.
Basically we are creating a new config WITH settings and then turning them off.
Presentation mode is a special mode that as I understand it, turns off
- Display Power Management
- Prevents screensaver from activating
- Prevents suspend and hibernation
*QSI = Quick System Info from menu (Copy for Forum) *MXPI = MX Package Installer *Please check the solved checkbox on the post that solved it. *Linux -This is the way!
@m_pav
The power supply is new, the graphics card is much newer than the board. The board is admittedly older, but as I wrote above, it has been running absolutely stable under Windows (on other hard drives that are not currently active) for months. I don't understand the other configuration you mentioned and I also want to run MX Linux in a stable manner in the version I have installed!
@CharlesV
I'll try to implement your suggestions and get back to you. Thanks!
Something else occurred to me: Since I'm switching from Windows and want to familiarize myself with Linux, I installed MX-Linux on a temporary SSD that is connected via a hot swap port. Maybe Linux can't handle it. I'll try deactivating hot swap in the BIOS to see if it runs more stable.
Something else occurred to me: Since I'm switching from Windows and want to familiarize myself with Linux, I installed MX-Linux on a temporary SSD that is connected via a hot swap port. Maybe Linux can't handle it. I'll try deactivating hot swap in the BIOS to see if it runs more stable.
That could be it. Hot swap in Linux can be very hit and miss.
HP 15; ryzen 3 5300U APU; 500 Gb SSD; 8GB ram
HP 17; ryzen 3 3200; 500 GB SSD; 12 GB ram
Idea Center 3; 12 gen i5; 256 GB ssd;
In Linux, newer isn't always better. The best solution is the one that works.
As far as the energy settings are concerned, I did everything as CharlesV said and then deactivated energy saving completely. Then I noticed that the screen still turned off after 10 minutes. So there must be another setting besides the xscreensaver and power manager settings that I don't know about. What could that be?
I also deactivated hot swap in the BIOS.
The problem seems to be a little better at the moment but the crashes still occur.
I would like to deactivate energy saving completely and don't know where the settings are or what needs to be deactivated.
lenalemon wrote: Sat Mar 01, 2025 5:11 am
As far as the energy settings are concerned, I did everything as CharlesV said and then deactivated energy saving completely. Then I noticed that the screen still turned off after 10 minutes. So there must be another setting besides the xscreensaver and power manager settings that I don't know about. What could that be?
I also deactivated hot swap in the BIOS.
The problem seems to be a little better at the moment but the crashes still occur.
I would like to deactivate energy saving completely and don't know where the settings are or what needs to be deactivated.
Forget hot swap altogether. Your Sandisk EMTEC X150 120GB SSD needs to be connected directly to one of the six SATA ports that you have onboard. See here (page 31 of the PDF) for their location: https://dlcdnets.asus.com/pub/ASUS/mb/L ... 87_PRO.pdf
HP 15; ryzen 3 5300U APU; 500 Gb SSD; 8GB ram
HP 17; ryzen 3 3200; 500 GB SSD; 12 GB ram
Idea Center 3; 12 gen i5; 256 GB ssd;
In Linux, newer isn't always better. The best solution is the one that works.
I have now connected the hard drive directly and performed a new installation, implemented all the settings mentioned, but it still crashes.
I have observed the crashing behavior again closely: If I do nothing on the Internet, especially if I don't open Firefox, it runs stable. It became unstable when using the package manager, but mainly because of Firefox (hardware acceleration is switched off). For example, when playing a YouTube video, sometimes (not always) the system freezes and can no longer be operated. If I run Windows with my hardware as an alternative, everything is stable with the latest Firefox.
So it could have something to do with the Linux graphics driver, but that's just a guess. I'm pretty frustrated at the moment and can hardly believe there's a solution. I'm thinking about installing the whole thing in Virtual Box, but that's only a stopgap solution for me.
As a test, install a liquorix kernel, we have found them to be very stable and resolve quite a few issues. I would suggest a 6.4 or 6.5 liquorix kernel as lighter for your machine.
*QSI = Quick System Info from menu (Copy for Forum) *MXPI = MX Package Installer *Please check the solved checkbox on the post that solved it. *Linux -This is the way!
Hello, installing the liquorix kernel didn't help either, it was unchanged afterwards.
However, I did install the AHS package with the 6.12.8-1-liquorix - amd64 kernel. After that, it ran stable for a while until the update packages reset something and it crashed again straight after.
In the package manager, under Kernel, there is a note that you should activate ahs for automatic updates. Can someone please tell me how to do this so that I don't go back to the normal version?
